External USB2 hard drives are a popular and practical choice for use with Ghost backups.  This guide is to provide a to show how to successfully use a USB2 drive with Ghost 10.

Most of the time USB2 and firewire drives work perfectly with Ghost 10.0, both in creating backups and in restoring files or partitions from the backup image stored on a USB2 drive.  Fortunately, as opposed to DOS/Ghost 2003, XP/Ghost 10.0 does not require any special drivers to be tried, tested, or installed to get USB2 drives to work.  Native support is built into both Windows XP and the Ghost 10 Recovery Environment (RE) CD.

The only problem that occasionally happens, occurs when the drive letter assigned by XP or the user, conflicts with the Ghost 10.0 RE.  For those cases, I shall address (1) how to avoid the problem in the first place, and (2) how to recover if you discover the problem.

Special thanks for Brian, Dan Goodell, El_Pescador, NightOwl, Pleonasm, Rad, and others for their input.




for any devices, whether internal or external.  Usually, these are hard-assigned by the user from
My Computer/Manage/Disk Management/drive volume/Change Drive Letter and Paths.
Reassign any conflicts if you have them.



If you discover that the Ghost 10.0 RE boot CD will not find or recognize your USB2 drive that contains your backup images, use the solutions in the following order.

, including other usb drives, thumbdrives, usb keys, digital cameras, card readers etc.  Reboot and try again with only your external hard drive attached.

Verify that your motherboard BIOS is the latest firmware level.  Check with the motherboard website to verify and get the latest BIOS.

If you have a USB mouse and/or USB keyboard, try using a PS2 mouse and keyboard.  Some motherboards have reported problems detecting other USB devices when booting from a USB mouse and keyboard.

, then the first and easiest approach is to modify the XP system registry:
1. Boot back to XP
2. Run Regedit, and navigate to the HKEY_LOCAL_MACHINE\SYSTEM\MountedDevices key.  Delete the \DosDevices\K: data-value where K: corresponds to the drive letter of your external USB2 drive.  Shutdown, and reboot back to the RE cd and try again.
3. For cases with multiple usb devices, you may have to delete all the \??\Volume... data-values as well as all the \DosDevices|... values.  If you do that, you will find however that you will have to reassign them once back in XP.

to modify the XP system registry:
1. Shut down
2. During startup, repeatedly hit F8 to enter the startup mode prompt.
3. Select Safe Mode
4. Continue to XP Safe Mode.
5. Run Regedit, and navigate to the HKEY_LOCAL_MACHINE\SYSTEM\MountedDevices key.  Delete the \DosDevices\K: data-value where K: corresponds to the drive letter of your external USB2 drive.  Shutdown, and reboot back to the RE cd and try again.


, then an alternate method is to zero-out the DiskID field of your external USB2 hard drive.  To do this:
1. Shut down Ghost 10.0 RE cd.
2. Disconnect your USB2 hard drive, and connect it to any functional Windows XP system.
3. Follow the procedures here to erase the DiskID fieldof your USB2 hard drive.
4. Reconnect your USB2 hard drive to your failed system, and retry from the Ghost 10.0 RE cd.



, and are booting into the Ghost 10.0 RE cd, you can remotely clear the same keys of your XP system using BartPE or ReatogoXPE program RegistryEditorPE. Follow the directions to clear the REMOTE_SYSTEM MountedDevices XP data-values, which  is found at:
My Computer\HKEY_LOCAL_MACHINE\_REMOTE_SYSTEM\System\MountedDevices key.


1. Use the BartPE or ReatogoXPE environment and copy (using the A43 File Management utility) the needed recovery point Ghost image to another destination that is visible from within the Ghost 10 recovery environment.


I hope this guide helps provide Ghost 10.0 users with an simple, almost foolproof approach to dealing with any problems related the external USB2 drives and Ghost 10.0.

Quote:

Thanks, I changed the title, because although most users have USB drives, I believe NightOwl said it applies to firewire as well.
Actually, I believe it applies to ANY drive, external or internal, whose drive letter can conflict the the RE cd.

I didn't include using another internal drive as a backup, because, most users purchase USB2 drives for backup.

The only problem with using A43 is that you have to find another target to copy the file to, and if your system is down, which partition or hard drive would you copy it to?

Thanks for your comments.

John, nice summary.

Pleonasm wrote on Apr 21^st, 2006 at 12:37pm:


What a great alternate idea.  Thanks.  I'll add using regedit in safe mode if possible.  However, regedit isn't one of the commands available in the Recovery Console (I just tried it again), unless someone else has an idea.  The Recovery Console is a minimal WinPE.

Thanks Pleonasm.